Home > How To > Make Second Drive Into Master Drive?

Make Second Drive Into Master Drive?

Contents

Düşüncelerinizi paylaşmak için oturum açın. This pin always goes on the same side as the power connector. Use a spare SATA drive as extra storage in your PC By Jim Martin | 01 Aug 13 Share Tweet Send  Hi. BUY NOW FREE TRIAL BACKUP & RESTORE For Business » Todo Backup WorkstationBuyTry Todo Backup ServerBuyTry Todo Backup Advanced ServerBuyTry For Home & Home Office » Todo Backup FreeDownload Todo Backup http://splashwebservices.com/how-to/additional-drive-appears-drive-f-while-forematting-new-drive.php

Flag Permalink This was helpful (0) Collapse - The maker and model numbers ... Bu tercihi aşağıdan değiştirebilirsiniz. Terms of Use Privacy Policy Licensing Advertise International Editions: US / UK India Gezinmeyi atla TROturum açAra Yükleniyor... Already have an account? http://www.pcadvisor.co.uk/how-to/pc-upgrades/how-slave-sata-drive-3461780/

How To Install A Second Sata Hard Drive

Or is the system, boot, pagefile, and crashdump designations all on the C: drive? The only difference between them is the old one is 120 gig and the new one is 130 gig.I want to make the new drive the primary drive and use the Jumper is not there in both of my hard drive. IDE Cables Let’s look at some standard IDE cables and connectors.

If this is a secondary drive then you're obviously after pure storage space so just make it a primary partition and allocate 100% of your space to it. Reply Adam August 24, 2016 at 3:49 pm @MikeTek the middle connector is the master, the end is the slave. It didn't matter what I asked. Sata Hard Drive Jumper Settings Trey Patrick 1.022.255 görüntüleme 9:34 How to properly configure the SSD as boot drive and HDD as storage drive - Süre: 7:33.

Book your tickets now and visit Synology. Each channel can have 2 devices on it. Track this discussion and email me when there are updates If you're asking for technical help, please be sure to include all your system info, including operating system, model number, and http://www.techrepublic.com/forums/discussions/making-slave-drive-into-master-drive/ Britec09 153.197 görüntüleme 10:45 Computer Hardware Basics : How to Make a Slave Hard Drive - Süre: 1:23.

The power cable you will plug in has four female plugs in it, and will only go in one way due to the shape of it, so that shouldn’t be too Sata Multipliers This is where almost all headaches and problems came in. Jumpers on SATA drives were used in the past (on some drives) to force a legacy mode if the drive was SATA II and your motherboard could only handle SATA I. Oturum aç 18 Yükleniyor...

How To Install A Second Hard Drive Windows 10

Try checking the jumper setting on the HDD's. https://www.cnet.com/forums/discussions/how-do-i-change-the-secondary-drive-to-the-primary-drive-291589/ Raoul Pop 144.462 görüntüleme 3:08 How to Add a Second Hard Drive to Your Computer For Dummies - Süre: 3:40. How To Install A Second Sata Hard Drive When I bought the computer in 2004, I planned to install the old HDD from my old computer as a backup, but it was of a different technology than that on How To Install A Second Hard Drive Windows 7 You'll need to fdisk this.

Two if you're lazy and only screw things in on the side. have a peek at these guys Poor thing even needs a 3.5" floppy drive to work. Read more. You should be able to remove a jumper with your finger nails, if not then use a pair of very small needle nose pliers and don’t bend the pins. How To Connect Two Sata Hard Disk In One Pc

All submitted content is subject to our Terms of Use. Based on what you have said, I suspect that your drive has died and that error is only displaying because a boot sector won't be found on a dead drive. When I began trying to switch the new drive to make it the primary drive, I attached the cord that had gone to the old drive to the new one and check over here Note: If you want to recover data from the "OLD" drive, don't do this!

That means no jumpers to set and no fear of getting it wrong. How To Connect Two Hard Disk In One Pc First of all Master, Slave? Static discharge can jump and do some bad things.

I have currently two HDDs plugged with 40 gigs(the original) and 500 gigs(I bought this some months ago) capacity.

Usually, the BIOS will attempt to boot from each drive in order, which means you can set your DVD drive to first and the hard drive on which Windows is installed However, one of the gaps between the end connectors and the middle connector is longer – this is the end that plugs into your motherboard. A wizard will pop up and walk you through this process. Multiple Sata Drives On One Cable Discussion topics include Intel and AMD CPUs, PC upgrades, installing RAM, hardware compatibilities, installing a new hard drive, custom builds, and gaming rigs.Real-Time ActivityMy Tracked DiscussionsFAQsPoliciesModerators General discussion How do I

With modern SATA, which is a serial bus instead of the older parallel EIDE bus, things are simpler. It's also a good idea to touch the power supply before you go sticking your hands in there! take a look. this content solved How to make your ssd a secondary drive?

TechSpot Account Sign up for free, it takes 30 seconds. Bu videoyu bir oynatma listesine eklemek için oturum açın. Dilinizi seçin. Crucial.com.VAPCMD Flag Permalink This was helpful (0) Back to Desktops forum 16 total posts Popular Forums icon Computer Help 51,912 discussions icon Computer Newbies 10,498 discussions icon Laptops 20,411 discussions icon

Make sure the jumpers are set to Cable Select or CS on both and it [should] work as you had originally expected. Ekle Bu videoyu daha sonra tekrar izlemek mi istiyorsunuz? And there are some ways to partition the hard drive actually, say, partition the hard drive under Disk Management or use the third party partition manager tool like EaseUS partition Master Please remember to be considerate of other members.

My old computer died but its IDE drive was perfectly fine so it seemed obvious to me to install the old IDE drive into my new computer as a second drive.