Home > What Is > What Is This? Microcontroller? How Do I Hook It Up? Warp-13a

What Is This? Microcontroller? How Do I Hook It Up? Warp-13a

Instructions for downloading and installing the sofware and help files can be found at http://www.junun.org/MarkIII/Warp13a.jsp. The HEX file is available free for you or a friend to program into a 18F252 update your WARP-13. Warp-13a 03 May 2015 #1 Fieldinator89 Windows 7 Ultimate 64-bit 59 posts Arizona What is this? The Warp-13a is an excellent programmer to fill the gap between the low end cheaper programmers and the quite costly PICSTART Plus.

Register Remember Me? The general layout is as in the popper roaster: the processor is obvious towards the right wires to LCD display and switches mainly attach to the right edge of the board Basically, it allows you to play games and do graphics-intensive tasks without a good video card, and maybe even without an accelerated card at all, using the CPU instead. The problem is that MPLAB insists that firmware version 4.10.0 needs to be on the board.

Go home to create chickens or pigs. There's more details on FTDI's product page, but it's a FT232RQ USB to serial UART interface chip ( datasheet here) embedded within the moulded usb connector. Brought to you by the letter E Mellon Head View Public Profile Find More Posts by Mellon Head What is this? I have no friends damnit!

Teardown Videos Datasheets Advanced Search Forum Digital Design and Embedded Programming Microcontrollers Picallw or Newfound Warp 13a Programmer? + Post New Thread Results 1 to 6 of 6 Picallw or If all else fails, ask someone for help! Sign up now! You will also need to provided your own serial cable, a straight-through extension cable.

I am trying to buy that ready, because I don't know how to do the procedures that NewFound Electronic asked. In order to make this as inexpensive as possible, the power supply and serial cable are sold separately. Below is a list of the test programs written to date. Blinking Both LEDs This test can be used on every stack board that contains a PIC (i.e. http://moonnightjobs.top/what-is-this-microcontroller-how-do-i-hook-it-up-warp-13a-90368 Cannibalising The controller is built from the controller I built for the popper-based roaster (and shown to the left).

How do I hook it up? The two wires running straight down the photo to the right of the chip are the I2C clock and data lines. (The bigger chip is just a divider chain - it It most likely attaches to your serial port, though I can't see the connector to be sure. The RTC chip has a device address of 1101000.

In short, a highly capable microcontroller on a single chip. http://www.junun.org/MarkIII/Info.jsp?item=20 Microcontroller? and this is as far as it has got ... These two ways are: Download directly from MPLAB by using the PICSTART Plus emulation feature of the Warp-13a Download using Newfound Electronics' stand-alone software.

See below for complete list of supported chips. NEWFOUND ELECTRONICS currently is not trading. ;-( Good luck! Fieldinator89 View Public Profile Find More Posts by Fieldinator89 03 May 2015 #4 Berton Windows 7 Ultimate 64-bit, Windows 8.1 64-bit, Mac OS X 10.10, Linux Mint 17, Windows 10 Support for the Warp-13a PIC Programmer Support for Warp-13a PIC Programmer is available through the members of the MarkIII Discussion Forum on Yahoo!

I have heard zero complaints about them. I should probably investigate and deal with them, but everything works so I can't be bothered. You need some free software to be able to write the programs for it and to make it work. The Warp-13a WINDOWS Software If you are not using MPLAB or simply want the ease and convenience of a standalone program, Newfound Electronics' Windows 95/98/ME/XP software is available free of charge

Firmware upgrades will be available from this site. Software Next, you'll need to download and install all of the necessary software to program, including the following: MPLAB IDE This software is used to develop, test, debug, and finally Lost password?

So I can wire a standard stereo jack socket direct to my microcontroller and using the magic cable plug straight into a usb port on the PC.

Privacy Policy Terms and Rules Help Popular Sections Electronics Projects Datasheets Resources Connect With Us Log-in Register Contact Us Forum software by XenForo™ ©2010-2015 XenForo Ltd. Instructions on how to do this will be posted when the next firmware release is available. The LCD backlight is now not under active control Main Board Additions There are some additions to the main board. You gratitude is for all to see.

I am told the Bluepole update will do the trick - apparently the advice is to simply use your Warp-13 to program a new PIC18F252 with the code and then substitute All rights reserved. Monitor(s) Displays Acer 24", Acer 22" Screen Resolution 3840 x 1080 Keyboard Logitech G710+ Mouse Logitech G500s PSU Corsair TX-750 Case CoolerMaster HAF 912+ Cooling Coolermaster Seidon 240M Liquid AIO. 6 http://i2.photobucket.com/albums/y11/davidl1l/cycle.png Network & Sharing How to use Windows Advanced Rasterization Platform (WARP)How to use Windows Advanced Rasterization Platform (WARP)(OS:w7) for gaming waiting for reply...

The Warp-13a firmware is designed to operate with this latest version of MPLAB - previous versions of MPLAB use a slightly different protocol and will be unable to communicate with the I am wanting to program 16F628, 16F874 and 16877. It then does a read and the RTC chip sends back the time - in this case it was ?:36:37. Several of each type are located in the lab for use. WARP programming board This piece of hardware serves as the bridge between your powered stack and the software located

ONLY a 16VDC or 12VAC power supply can be used with the WARP board! How do I hook it up?